High Frequency RFID Gate Smart Card Reader

Basic Info

Model NO.	RFH-1332-114C
Function	Encrypt/Decrypt, Identification
Structure	RFID Card
Data Transmission Mode	Parallel
Application Field	Non-Fiscard
Specification	PBT+ABS
Trademark	yuanben

Product Description

High Frequency RFID Reader (13.56 MHz)
TCP/IP Series

1.Overview
The RFID (Radio Frequency Identity) RFH-1332-114C is a non-contact high frequency RFID reader, specially designed for use in embedded applications such as address reading or proximity control of AGV and other industrial application. It can be worked in a variety of harsh environments. The RFID reader has anti-collision function, its operating frequency is 13.56MHz.

2. Key Features
Comply with ISO14443A protocol and support M1 card and so on.
Support NXP CODE I, CODE SLI and other tags in line with the ISO15693 Protocol.
Support reading and writing, complies with ISO/IEC 18000-3 Mode.
Ethernet interface,TCP/IP protocol.
Built in RFID antenna (Integration Design of Reader and Antenna)
Read / write distance 70-90mm (industry Environment).
reading time less than 20 millisecond per 8 bits. no data mistake
Good package IP65, PBT engineering material suit industry environment application

3. Applications
It is mainly used in material management of production line, intelligent parking lot, AGV, electronic label reading and writing of forklift positioning management system.

4. Technical Data sheet

Operating Frequency	13.56MHz
Working Voltage	10-30Vdc
total power	2W
Standard protocol	ISO/IEC 15693 and 14443A
Compliance interface	ISO18000-3 mode
Maximum Reading distance	70-90mm
Reading time	20ms/8 bit
Interface	Ethernet
Indication	4 Led
Working Temperature	-10ºC~+70ºC
Storage temperature	-20ºC~+85ºC
Working humidity	<90%
Cable	M12 connectors
Color of Housing	Green Housing.
Material of Housing	PBT+ABS
Dimension	As attached drawing
IP class	IP65 Industry Environment

5. Dimension and picture

 

Installation location dimension:4-φ3mm*6mm

 

6. Wiring Diagram

7. RFID Sensor with Host Computer Communication Data Packet Format

This data message format is used for communication between the RFID (HF) sensor and the host computer (controller). The host computer sends commands (downstream) and the RFID sensor responds (upstream).
Command format

Frame header 01

Data length

Data1

Data2

…

Data N

Checksum (CAL)

End of frame FD

Data length:The length of the Data1~Data N(=N);
Checksum(CAL):From the data length to Data N (N+1 number) sum, take the lower 8 bits.
Note:The data is a hexadecimal number in the table.

1. Start to read tag
2. Stop reading tag
3. Reading 15693 tag data

01

02

42

47

8B

FD

01

02

45

44

8B

FD

01

03

54

52

Block number(0-1bit)

CAL

FD

Respond

01

04

XX

XX

XX

XX

CAL

FD

Where from 3 to 6 byte is read data (4 bytes).

1. Writing 15693 tag data

01

07

54

57

Block number (0-1B)

XX

XX

XX

XX

CAL

FD

Where from 6 to 9 byte is written data (4 bytes)
Respond (success)

01

04

53

55

43

43

32

FD

1. Reading Mifare tag data(S70 card)

01

03

4D

52

Block number(0-3F)

CAL

FD

Respond(success)

01

10

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

CAL

FD

Where from 3 to 18 bytes are read data(16 bytes).

1. Writing Mifare tag data(S70 card)

01

13

4D

57

Block number (0-3F)

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

CAL

FD

Where from 6 to 21 bytes are written data (16 bytes).
Respond(success)

01

04

53

55

43

43

32

FD

Instruction:

1. The RFID sensor automatically reads the tag when it is turned on.
2. The RFID sensor reads the data stored in the tag automatically when the tag is in reading area.
3. The RFID sensor stops reading the tag automatically after receiving the command to stop reading; and it can be restarted read the card after receiving the reading tag command.
4. when the mifare tag is used, block cannot be read and written with block numbers 3+4n (n=0, 1, 2...), In other words, the blocks cannot be read and written with blocks numbers 3,7,11....

8. How to configure WEB server
8.1 After connecting RJ45 to PC and supply the power to the reader, start the computer's WEB browser.
8.2 Specify the IP address of the reader in the address bar of the WEB. The factory setting of the IP address is http://192.168.1.200/